PurgEye 200 IP65 Hand Held Purge Monitor
Argweld PurgEye 200
Rechargeable Weld Purge Monitor is a high accuracy hand held unit that reads oxygen content down to 0 to 10 ppm.
Description
Argweld PurgEye 200 Hand Held Purge Monitor, comes with an integral electro-mechanical vacuum pump and a rechargeable battery.
This Hand Held Purge Monitor can be used as a continuously reading instrument with free flow of the purge exhaust gas across the sensor, or as a sampling instrument with the integral electro-mechanical vacuum pump. The unit is a residual oxygen monitor used to measure the quality of purge in the weld area.
The Argweld® PurgEye® 200 Rechargeable Weld Purge Monitor® contains 4 standard rechargeable AA batteries and is supplied with a rechargeable battery unit and charger.
The large alpha-numeric display is easy to read and can be easily switched to display readings in ppm or percentage.
The Argweld® PurgEye® 200 Rechargeable Weld Purge Monitor® has a working temperature between 0 and 70°C (32 and 158°F) and a two minute warm up time.
Note: Use only 6mm OD polyurethane weld purge tubing. The leak tight quick fit couplings are specifically integrated so that the user will not have leaks of air into the critical purge zone. Do not use other tubing because it will not fit properly and it will cause leaks.
JEI PurgEye Family Table API-WEB-PThe Argweld PurgEye 200 Rechargeable Weld Purge Monitor® is small, lightweight, hand held and rechargeable battery powered.
The Purge monitor or Residual oxygen sensor is ideal for monitoring oxygen content when wlding exotic materials or weld environments requiring very low oxygen content.
Some of the great features of the Argweld PurgEye 200 are:
Hand Held Purge Monitor
Compact form factor, easily transportable and can be used in small areas
Warning Alarm
The warning alarm can be set to any level between 1 and 999 ppm and has both audible and visual indication when the alarm threshold is exceeded.
Flow Detection
The flow warning exclamation icon will be displayed whenever the flow of sample gas drops below the minimum flow rate required for an accurate reading. Please note, this could be due to a blocked filter in need of replacement.
Integral Sampling Pump
With the Argweld PurgEye® 200 switched on and the alarm inactive or muted, pressing the standby button will turn the integral sample pump on and off.
Alarm Mute
If the alarm is sounding, then pressing the standby button will mute the alarm, subsequent presses will control the sample pump.
Alarm + and Alarm – Buttons
Pressing either of the alarm buttons will display the current alarm threshold setting. When the alarm threshold is displayed, the first digit will flash, pressing either of the alarm buttons at this point will increase or decrease the value of the flashing digit.
Large Character LCD Screen
The large LCD screen allows the reading to be easily read and helps conserve battery power compared to other display technologies.
Rechargeable Battery
The Argweld PurgEye® 200 has been specifically designed to be rechargeable battery powered.
Auto Power-Off
If the PurgEye® 200 is left with an over-range reading for more than 15 minutes, then it will automatically turn off to conserve battery power.
Power On / Off
If the PurgEye® 200 is off, then pressing the standby button will switch it on and it will start the sensor warm-up procedure. The PurgEye® 200 can be turned off by holding the standby button for approximately 10 seconds or until it turns off.
Lightweight
Weighing only 400 gms (without batteries), the instrument is really lightweight, easy to use all day long.
Guaranteed Accuracy
The PurgEye® 200 Weld Purge Monitor® indicates oxygen levels from 1000 ppm down to 10 ppm (0.001%), so use an Argweld® PurgEye® Weld Purge Monitor® everytime for guaranteed accuracy of oxygen indication to allow a weld start with minimal risk of oxidation.
Supplied with:
8 x AA rechargeable batteries (4 in use & 4 in charger at all times)
Rechargeable battery unit with mains adaptor
Sample tube set with filter (150 mm green tubing and 1 metre clear tubing with filter) (as per models PurgEye® 300 & 500)
Neck or wrist safety lanyard
User instruction booklet
Storage and presentation case
Calibration Certificate for the purpose of Quality Control Procedures and Management Systems
Measuring Range: 1000 ppm (0.1%) down to 10 ppm (0.001%)
Accuracy : ± 0.002% (20 ppm)
Battery Type : Battery type 4 x rechargeable AA (included)
Screen: LCD (Liquid Crystal Display) 25 mm high x 60 mm wide
Weight : 400 gms (without batteries)
The unit is manufactuered in UK . Click here to view Product Videos